When used correctly, hydraulic power is one of the safest methods of applying force to your work. And to that end we offer some DO’s and DON’Ts, simple common sense points which apply to practically all Enerpac hydraulic products.
• Lift slowly and check the load often
• Avoid standing in the line of force
• Anticipate possible problems and take steps to avoid them.
The line drawings and application photos of Enerpac products throughout this catalog are used to portray how some of our customers have used hydraulics in industry.
In designing similar systems, care must be taken to select the proper components that provide safe operation and fit your needs.
Check to see if all safety measures have been taken to avoid the risk of injury and property damage from your application or system.
Enerpac can not be held responsible for damage or injury, caused by unsafe use, maintenance or application of its products. Please contact the Enerpac office or a representative for guidance when you are in doubt as to the proper safety precautions to be taken in designing and setting up your particular system.
In addition to these tips, every Enerpac product comes with instructions spelling out specific safety information. Please read them carefully.
Enerpac Safety Video
Provide a level and solid support for the entire jack base area.
The entire jack saddle must be in contact with the load. Movement of the load to be in the same direction as jack plunger.
Never place any part of your body under the load. Ensure the load is on a solid support before venturing under.
Remove the jack handle when it is not being used.
Provide a solid support for the entire cylinder base area. Use cylinder base attachment for more stability.
The entire cylinder saddle must be in contact with the load. Movement of the cylinder must be parallel with the movement of the load.
Do not use cylinder without saddle. This will cause plunger to ”mushroom”. Saddles distribute load evenly on the plunger.
As with jacks, never place any part of your body under the load. Load must be on cribbing before venturing under.
Always protect cylinder threads for use with attachments.
Keep hydraulic equipment away from open fire and temperatures above 65 °C (150°F).
Always read instructions and safety warnings that come with your Enerpac hydraulic equipment.
Don’t override the factory setting of relief valves. Always use a gauge to check system pressure.
Don’t use handle extenders. Hand pumps should be easy to operate when used correctly.
Close release valve finger tight. Using force will ruin the valve.
Fill pump only to recommended level. Fill only when connected cylinder is fully retracted.
Use only genuine Enerpac hydraulic oil. Wrong fluid can destroy seals and pump and will render your warranty null and void your guarantee.
Hoses and Couplers
Clean both coupler parts before connecting. Use dust caps when coupler parts are not connected.
Detach cylinder only when fully retracted or use shut-off valves or safety valves to lock-in cylinder pressure.
Keep hoses away from the area beneath loads.
Don’t kink hoses. Bending radius should be at least 60 millimetres. Don’t drive over or drop heavy objects on hoses.
Don’t lift hydraulic equipment by the hoses.
Never allow the cylinder to be lifted off of the ground through the couplers.
TECHSYSTEM Industrial Technology - the power of modern solutions.
Naše společnost je v České republice a na Slovensku výhradním zástupcem takových renomovaných firem, jako jsou: KILEWS – průmyslové elektrické šroubováky a aku šroubováky s nastavitelným krouticím momentem; RAD – pneumatické, elektrické a aku dynamometrické klíče s velmi velkým krouticím momentem; TECNA – závěsné balansery; BNP – reakční ramena a stojany a polohovací systémy; JEIL MTECH – průmyslové mikro příklepové a laserové značkovací výrobky s názvem MARKSMAN; TORERO a AIR PRO – průmyslové šroubováky a pneumatické klíče s nastavitelným krouticím momentem; TORSION X a LARZEP – systémy silové hydrauliky.
TECHSYSTEM I.T. kromě obchodní činnosti také poskytuje služby.